Search

Search

Home / EC Buying / Cables & Accessories
FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter in Kuwait

FT200XD CJMCU-200 USB to Serial Adapter USB to I2C Serial Module IIC Port TTL Level Input CMOS Output Transfer Convertor Serial Adapter

KWD 5
Brand
EC Buying
Weight
29 g
– 1 +

Special Features

  • Overview ：The FT200XD is a package and pin optimised USB to I2C interface device which simplifies USB to I2Cdesigns and reduces external component count by fully integrating an external EEPROM and a clock circuit which requires no external crystal in a small form factor 3x3mm 10 pin package. It has been designed to operate efficiently with a USB host controller by using as little of the total USB bandwidth available as possible.
  • Features: FT200XD is a monolithic USB to I2C interface. Up to 3.4MHz, high-speed mode, supporting I2C. Unique USB FTDIC chip ID Feature, FT200XD can be configured with CBUS I/O pin. It can send and receive LED driving signals. The FT200XD can be used as an integrated+3.3V level converter for USB I/O.The single operation power supply is+5V. There is a 3V3/1V8 LDO regulator inside. UHCI/OHCI/EHCI host controllers are compatible. USB 2.0 full speed compatibility.
  • Application: FT200XD can upgrade traditional peripherals to USB, and use USB to increase system modularization. FT200XD can be applied to USB instrument, USB industrial control and USB digital camera interface. The FT200XD can monitor the motherboard and system through USB. FT200XD can also be combined with USB interface to enable PC transmission as development system communication.
  • Low Power Consumption：The FT200XD is capable of operating at a voltage supply between +3.3V and +5V with a nominal operational mode current of 8mA and a nominal USB suspend mode current of 125µA. This allows greater margin for peripheral designs to meet the USB suspend mode current limit of 2.5mA. An integrated level converter within the I2C interface allows the FT200XD to interface to I2C logic running at +1.8V to +3.3V (5V tolerant).
  • USB transceiver. The USB transceiver unit provides a USB 1.1/USB 2.0 full speed physical interface to connect to the USB cable. The output driver provides+3.3V level conversion rate control signal input receiver and two single end input receivers provide USB data reset detection conditions respectively in, single end 0 and USB. Functions include 1.5k Ω pull-up resistor on USBDP. The module also detects when a USB power supply is connected.

Description

Description: The single chip USB to I2C interface has a high speed mode of up to 3.4 MHz. It supports the whole USB protocol on I2C chip, and does not require USB specific firmware programming. The fully integrated 2048 byte multi time programmable (MTP) memory is used to store device descriptors and CBUS I/O configuration. The fully integrated clock generation does not require an external crystal oscillator, plus optional clock output options, It can realize seamless interface with external MCU or FPGA, 512 byte receiving buffer and 512 byte sending buffer USB power supply configuration, support bus powered, self powered and bus powered power switch integration+3.3V level converter, used for 3.3VCMOS driver output and TTL input of USB I/O, can work to 1V8 through external pull-up resistance, and can withstand 5V input configurable I/O pin output drive strength, Small 4mA and large 16mA integrated power on reset circuit fully integrated AVCC power filter - no external filter required+5V single power supply internal 3V3/1V8 LDO regulator.

Related Items

{"error":"Error","cart_limit":"You have too many items in your cart.","prod_limit":"You cannot add any more of this item"}